08-01-2012, 12:36 AM
This months update is very picture heavy!
For the Reliant update I've decided to tackle this model's Aztec Pattern first because there is a difference in the pattern from the Enterprise Aztec Pattern. Not only that but there is far more detailwork that needed to be done with the upper saucer section than with the Enterprise models. In fact the detailing on Reliant is the most detail work that I've ever put into any single model EVER! I was very pleased with the way it has turned out. I was also able to put on most of the Decals in this update. The one thing I didn't realize when I recieved this kit was that other than the markings around the hatches there were no red stripe decals that came with this model, so I decided to paint them all on myself. I was able to use Insignia Red as the color of choice and it turned out to be a good choice. There is very little difference between the Decal Red and the Painted on stripes as you will see in the pics. For the shoulder part or rear of the upper saucer there is a grid pattern that can be seen on the filming miniature, so I had to put this on the model first. It can be seen as very thin blue lines of masking tape. Then I was able to add all of the different shapes of pre-cut masking tape to the insides of each of these grid boxes. The results came out excellent when the tape was removed. I've also painted up the top and underneath aft section which at first threw me as to the color. A picture of the original Reliant revealed that some of these sections appeared to be a light blue or gray color. But when I reviewed ST:TWOK a saw that all of these details were dark. So, before I messed this part up I began to decide what this color was. It was very difficult to determine on the screen. I happened to have an AMT/ertl Reliant kit and was just curious to see if the instructions had any hints of wjat colors to use. In this case it suggested Intermediate Blue, which I had never heard of, but I looked it up on-line and found that Model Master Paints did in fact have this color, so I tried it out and then compared it to the pictures I have of the original filming miniature and sure enough, it was a very spot on match which was a complete relief to me. I also realized at this point this is a common color used on smaller parts of the ship such as the torpedo launchers and some of the Interior parts for the hatches that I am putting into the Enterprise builds. So with a big sigh of relief I can move onto to other parts of this model. I put a color comparison picture of both my build and the Filming miniature in the update so you can decide for yourselves wether or not the build looks as close as possible to the filming miniature. Let me know what you think.
See you next update! Enjoy! And as always comments and New members are always welcome!
Mark
For the Reliant update I've decided to tackle this model's Aztec Pattern first because there is a difference in the pattern from the Enterprise Aztec Pattern. Not only that but there is far more detailwork that needed to be done with the upper saucer section than with the Enterprise models. In fact the detailing on Reliant is the most detail work that I've ever put into any single model EVER! I was very pleased with the way it has turned out. I was also able to put on most of the Decals in this update. The one thing I didn't realize when I recieved this kit was that other than the markings around the hatches there were no red stripe decals that came with this model, so I decided to paint them all on myself. I was able to use Insignia Red as the color of choice and it turned out to be a good choice. There is very little difference between the Decal Red and the Painted on stripes as you will see in the pics. For the shoulder part or rear of the upper saucer there is a grid pattern that can be seen on the filming miniature, so I had to put this on the model first. It can be seen as very thin blue lines of masking tape. Then I was able to add all of the different shapes of pre-cut masking tape to the insides of each of these grid boxes. The results came out excellent when the tape was removed. I've also painted up the top and underneath aft section which at first threw me as to the color. A picture of the original Reliant revealed that some of these sections appeared to be a light blue or gray color. But when I reviewed ST:TWOK a saw that all of these details were dark. So, before I messed this part up I began to decide what this color was. It was very difficult to determine on the screen. I happened to have an AMT/ertl Reliant kit and was just curious to see if the instructions had any hints of wjat colors to use. In this case it suggested Intermediate Blue, which I had never heard of, but I looked it up on-line and found that Model Master Paints did in fact have this color, so I tried it out and then compared it to the pictures I have of the original filming miniature and sure enough, it was a very spot on match which was a complete relief to me. I also realized at this point this is a common color used on smaller parts of the ship such as the torpedo launchers and some of the Interior parts for the hatches that I am putting into the Enterprise builds. So with a big sigh of relief I can move onto to other parts of this model. I put a color comparison picture of both my build and the Filming miniature in the update so you can decide for yourselves wether or not the build looks as close as possible to the filming miniature. Let me know what you think.
See you next update! Enjoy! And as always comments and New members are always welcome!
Mark
"... once it's activated, there's no way to stop it!" - Scotty - DMa