Login

3d-builder · (This post was last modified: 11-17-2009, 07:33 AM by 3d-builder.)

I have most of this on the RI so I will post a link to it,
and continue the present build here.
http://resinilluminati.com/showthread.php?t=8152

The latest is here

Ah....
After cutting the f-16 like intakes out on the bandsaw I needed a way
of cutting them in half. I could have used the band saw but didn't want
to loose the thickness of the blade on the pattern.

So I used this "Real" thin saw I had from Micro-mark,
to keep the saw cutting at 90deg I used two 123 blocks
to guide it.
[Image: 100_1780.jpg]

Next up some vector rings, that go at the rear of the engines
just some PVC cut and filled with some 2 part modeling clay.
[Image: 100_1789.jpg]

For scale the ring on the left is a SS size vector ring!! Smile

ext I just took the remaining clay I had and started to fill in the cross
sections.Every thing in this pic is pretty lumpy but will get sanded!
[Image: 100_1793.jpg]

This pic shows some sanded parts canopy, canopy bulkhead,
1 engine set, vector rings, rear intakes.
[Image: 100_1795.jpg]

Thats about where i am at for the moment!

scratchy · 11-25-2009, 05:11 PM

Wow, I've always wanted to try the A-Wing, but never really knew how to start it.

Looking Good!

3d-builder · 11-30-2009, 02:18 AM

(11-25-2009, 05:11 PM)scratchy Wrote: Wow, I've always wanted to try the A-Wing, but never really knew how to start it.

Looking Good!

Well if this thread helps go ahead and try!!: Wink

***JAWS*** · 11-30-2009, 06:42 AM

Well with your current abillities scratchy I don't think your going to have too much trouble with anything you would like to build Cool

Michael watching you make this has also given me a fantastic insight to the process needed to form shapes. Its truly humbling to guys like yourself & scratchy that make stuff from nothing show how you get there. Thanks guys. Im going to give it a go sometime Big Grin

Nice work on the AWing Iding at the RPF too Michael. You guys are killin it.

3d-builder · (This post was last modified: 01-27-2010, 02:56 PM by 3d-builder.)

(11-30-2009, 06:42 AM)jasonwright.1972 Wrote: Well with your current abillities scratchy I don't think your going to have too much trouble with anything you would like to build Michael watching you make this has also given me a fantastic insight to the process needed to form shapes. Its truly humbling to guys like yourself & scratchy that make stuff from nothing show how you get there. Thanks guys. Im going to give it a go sometime Nice work on the AWing Iding at the RPF too Michael. You guys are killin it.

Thanks Jay!
Here is a picture with most of the patterns filled with clay!
[Image: 100_1929.jpg]

The hull up on the platen ready for forming.
[Image: 100_1932.jpg]

Formed got some webbing away from the pattern...got lucky probavly heated
a few minutes long but the pull was still very good!
[Image: 100_1934.jpg]

This former was a bit to small for all those parts but I
salvaged most of them!! Dodgy

The pattern's bottom profile is built up on a piece of 3mm styrene,
this protects the clay when you cut away the flash. But after removing
the riser and cutting away the flash it creates, I still have to take away
the 3mm. So cut some masking tape 3mm wide and lay it down around
the part. Mark with pencil and sand....
[Image: 100_1937.jpg]

Then it's time to find the center on both top
and bottom hulls, and mark other ares that need to be
cut away.
[Image: 100_1944.jpg]

Then it's mr dremel too;s time.
[Image: 100_1945.jpg]

A little rough but hand sanding for the rest.
[Image: 100_1947.jpg]

The seams are nice and tight, so time to mark out the missile launch tubes.
[Image: 100_1962.jpg]

Small dremel tool bit to the rescue and a steady hand!
[Image: 100_1963.jpg]

Finished repeat for the other side.
[Image: 100_1964.jpg]

Now mark out the center insert and cut it away.
[Image: 100_1951.jpg]

Dremel away again.
[Image: 100_1952.jpg]

Then clean it up, repeat for lower hull.
[Image: 100_1954.jpg]

Small mock up on top hull against SS A-wing for scale.
[Image: 100_1926.jpg]

Same thing here cut away the gun well openings
on each side.
[Image: 100_1949.jpg]

I used some evergreen channel strips
on the inside of the missile launch tubes,
looked and fit great!
http://i8.photobucket.com/albums/a40/3di...0_1972.jpg
In these to pics you can see the the inner
bulkheads on each side, they really firm things up. Also
the channel strip behind them.
http://i8.photobucket.com/albums/a40/3di...0_1972.jpg
[Image: 100_1973.jpg]

You have seen in prior pics the canopy bulkhead
already in place. Just find and mark the center
so it can be fitted correctly.The back has to be cut away
and then recessed with a fresh piece of plastic.
[Image: 100_1970.jpg]

Make a template for the center cut out.
[Image: 100_1977.jpg]

This model is 2x bigger than the small snap kit offered in the 80's
in the pic the center insert is checked against the small kit.
The width was exactly 2x's bigger.
[Image: 100_1986.jpg]

Again you have seen this part the canopy/nose and rail
it is created by dremeling out the un-needed plastic,
This area is drawn on the plastic part before cutting.
[Image: 100_1950.jpg]

3d-builder · 01-27-2010, 03:06 PM

Center section mocked in only with panel lines
on it and most of the other areas. The center sections panel
lines were scribed before it was fitted.
[Image: 100_1994.jpg]

center section panel lines scribed.
scribing side pales on a curve? try some evergreen strip and tape it down.
[Image: 100_1999.jpg]

All panels finished.
[Image: 100_2025.jpg]

***JAWS*** · 01-27-2010, 05:10 PM

That is just freakn sick man! Thanks for the whopper update. It was worth the wait!

3d-builder · (This post was last modified: 01-28-2010, 05:17 AM by 3d-builder.)

No worries glad you liked it!

Just want to get this up to speed so I can check out the rest of the site here.

Ok on to the rear where the inner bulkhead lives,
I put in some strip to locate the depth of the bulkhead.
[Image: 100_2067.jpg]

Here is the bulkhead with two right triangles attached
to make sure it sits up at 90 deg.
[Image: 100_2063.jpg]

Fitter up against the strips I mentioned earlier.
[Image: 100_2071.jpg]

To this same assembly I added the gun well bulkheads,
on the sides and backed them up with right triangles as well
because they need to be drilled out for the cannons later.
[Image: 100_2066.jpg]

Ok all in place!
[Image: 100_2073.jpg]

Time to dremel out the opening for the cockpit tub.
[Image: 100_2049.jpg]

After that is done I place a peice of styrene underneath
to capture the shape of the opening, the objective is to
make a plug for forming for the tub.
[Image: 100_2058.jpg]

From there I just build up on the plastic
with some pine 22mm high.
[Image: 100_2076.jpg]

And here it is the formed tub.
[Image: 100_2078.jpg]

This is the bottom hulll cut away just like the top, except there is a ramp
down there, that will have to be made later.
[Image: 100_2044.jpg]

center section mocked in with some panel lines
drawn but not all.
[Image: 100_2043.jpg]

Now some detailing in the tub.
[Image: 100_2084.jpg]

Still more detailing needed in the tub, need to make controls
and seat.

A few mocked up pics with stabilizers,
and the rear F-16 like intakes I made out of poplar
and then hollowed, going to have these cast for me.
[Image: 100_2075.jpg]

9 line · 01-30-2010, 05:40 AM

Michael, thats looking great, your the vacuum forming king.

***JAWS*** · 03-22-2010, 11:48 AM

Hey Michael love that kit parts box you have there. Any updates on the A? Is it right you were making this as a patern for a kit?

03-22-2010, 05:49 PM

I was just admiring the balsa parts on this build. I never knew that it could look so good, and be so useful! I'm also wondering the same thing Jase is - are there any updates on this?

3d-builder · (This post was last modified: 09-16-2011, 12:46 PM by 3d-builder.)

I can make main parts available that you see in the videos
after I know it's going to work.....as you can see it would be
for advanced builders with a bit of scratch building experience. Big Grin

Login
Username/Email:
Password:	Lost Password?
	Remember me